Jeep Part Sales

Alloy USA Rear Driver Side 1-Piece Performance Axleshaft For 1976-79 Jeep CJ Series With QuadraTrac AMC Model 20 Axle One Piece Replacement Axle Shaft AMC Model 20 29 Spline 5 on 5.5in. Bolt Pattern 30.437in. Overall Length Driverr Side Does NOT Include Bearings Seals Or Studs For Use In 76-79 Jeep CJ Quadratrac Don’t just replace your axle shafts, upgrade them. For less than the cost or an original replacement axle shaft you can upgrade to an Alloy USA performance shaft. Our axles... Read More Learn More

Alloy USA Rear Driver Side 30 Spline Performance Axleshaft 2007-12 Jeep Wrangler JK Models With Dana 44 Axle Rubicon (Dual Bolt Patterns) Dana 44 Rubicon 32 spline: 30.79 inches long Driver Side Bearings and seals sold separately Alloy USA Replacement Axles are designed as direct replacements for original equipment axle shafts without modifications. They are sold as individually and do not include bearings or seals. They are an efficient, low cost replacement for a broken shaft. Original... Read More Learn More

Alloy USA Replacement Axles are designed as direct replacements for original equipment axle shafts without modifications. They are sold as individually and do not include bearings or seals. Learn More

Alloy USA Rear Passenger Side 30 Spline Performance Axleshaft For 1997-06 Jeep Wrangler TJ With Dana 44 Axle Replacement Axle Shaft Dana 44 30 Spline 5 on 4.5in. Bolt Pattern Passenger Side Does NOT Include Bearings Seals Or Studs For Use In 97-06 Jeep TJ With Dana 44 With Out ABS Don’t just replace your axle shafts, upgrade them. For less than the cost or an original replacement axle shaft you can upgrade to an Alloy USA performance shaft. Our axles are made from 1541H or 4140 steel... Read More Learn More

Now a serviceable U-joint for Dana applications is available to you. Replace your 5-297X or 5-760X U-joint with Alloy USA's new X-joint! Serviceable grease Zerk at each cap allows you to flush grime and fill with grease to ensure that your X-joints will last for when you need them. Dependable cold forged steel composition made of chromium, molybdenum and nickel alloy. Hardened case for excellent wear resistance. Full circle clips as well as half clips included. Fits These... Read More Learn More

Part Number: RD100 Dana Model 30 Front Axle 27 Spline Gear Ratio 3.73 & Up * Quadradrive traction control vehicles require non-Quadradrive axle shaft replacements for Air Locker installation. Learn More

With the ARB Air Locker locking differential system, you can control your vehicle's on and off road performance from inside your Jeep with the push of a button. Learn More

Part Number: RD82 FordModel 8.8 Axles 28 Spline Gear Ratio All Ford Explorer, Ranger 1990 & Up Axle Upgrade for the Jeep YJ & TJ Wranglers. An Explorer 8.8-inch is a popular swap for Wranglers because it's almost exactly the same width as the stock Wrangler axles and thus requires no width modifications. The Explorers used the same wheel bolt pattern as a TJ & YJ Wranglers. Ranger VS Explorer: The Rangers use a 28-spline 8.8-Inch axle on 4.0 Liter engine applications and a 31-spline... Read More Learn More

Only the toughest bumper known to man! These bumpers offer unmatched quality, protection, strength and style and weigh in the 90-100 pound neighborhood. Learn More

Air bag compatible and incorporates a sculptured wing design for the best possible fit and appearance. With press formed provision for factory fog lights, the bar also incorporates Hi-Lift jacking points, 2 CB brackets on the center tube and winch provision. Learn More