Driveshaft - Rear

Will only work on fixed yoke style slip yoke eliminator 1310 series yoke Spicer drive shafts and components are as good as they get. This drive shaft is compatible with the RE1811 Slip yoke eliminator kit, Atlas transfer cases and any other 1310 series CV yoke. Measurements are taken center to center on the u-joint with the slip stub at the center of it's travel. measure your vehicle on the ground in the running position to get correct length. Fits These Vehicles: 87-95 Jeep Wrangler... Read More Learn More

Rubicon Express Rear CV Driveshaft T-Case Adapter Flange 2007+ Jeep Wrangler JK 2 Door & Unlimited 4 Door Billet aluminum flange 8mm-1.25 x 25mm socket cap screws Rear transfer case flange adapter. Must be used with the following drive shaft part numbers: #RE1887-240 (2-door) and RE1887-430 (4-door). Learn More

1948-1971 Jeep CJ5 (CJ2a Serial # 13453 & Up) rear Drive Shaft 4 Cyl & 3 Speed Alternate Part # 906932 Learn More

Yukon Drive Shafts Fit 2018+ Jeep JL 4 Door Wranglers With Dana 35 (M200) Rear Axle Spicer 1310 U-Joint Size Is Suitable for Jeeps Running A Maximum Tire Size of 35" Ample Slip For Stock Wrangler Suspensions Up to 4 ½” lift, Long Arm Kits and Suspensions Over 4 ½” Will Have To Measure In Order to Verify Fitment. This Measures 45.25" from U-Joint to U-Joint Learn More

1997-06 TJ Wrangler Bare Steel Fits 3.5 - 6" lift for Mega Short SYE ONLY CV Style Custom designed drive shaft for use with our Mega Short Slip Yoke Eliminator kit. Works in combination with the Mega Short SYE on 97-06 Jeep Wranglers with a suspension lift of 3.5"to 6". Each of these double cardan CV style drive shafts replaces your single U joint drive shaft. Each drive shaft has been pre-balanced and has 3 zerk fittings for ease of lubricating. This ready to go drive shaft is a must... Read More Learn More

2007-15 JK Wrangler and Rubicon 2-Door Double-Cardan joint Direct bolt on drive shaft Extended Length = 22.50" Compressed Length = 26.50" 1310 U-joints New original equipment JK Wranglers use drive shafts that have Rzeppa CV joints similar to most front wheel drive cars. These CV joints are fine for normal car applications but when you lift your Jeep or put on larger tires and drive your Jeep off road, these joints are not up to the task! Rugged Ridge has developed a solution for this... Read More Learn More

The Teraflex High-Angle Rzeppa CV Conversion Yoke allows you to convert U-joint style yokes to accept a Rzeppa style CV driveshaft. Learn More

This double cardan style CV drive shaft is recommended for Jeep TJ Wrangler models equipped with 4in - 6in suspension lifts to prevent driveline vibration and the rear output shaft from breaking. Learn More

Will only work on cut and tap flange style slip yoke eliminator 1310 series yoke Spicer drive shafts and components are as good as they get. This drive shaft is compatible with the RE1807, RE1801 Slip yoke eliminator kits and Currie Enterprises tail shaft conversion kits. Measurements are taken from flange face to center of the rear u-joint with the slip stub at the center of it's travel. measure your vehicle on the ground in the running position to get correct length. Fits These Vehicles:... Read More Learn More

This double cardan style CV drive shaft is recommended for Jeep XJ Cherokee models equipped with 4in - 6in suspension lifts to prevent driveline vibration and the rear output shaft from breaking. Learn More