TeraFlex

Designed to carry up to a 37" tire over the most extreme trails and obstacles, and provide easy and immediate access to the rear cargo area with a single action while spreading the load and weight of the tire to more than just one hinge point. Learn More

These TeraFlex TJ/LJ Heavy-Duty Large Taper Tie Rod Ends utilize a one-ton joint end and a large taper rod end to fit a standard Dana 60 front axle or a Tera CRD60 axle. Learn More

TeraFlex JK/JKU Heavy-Duty Ball Joints are engineered to handle the increased load caused by oversized tires and offset wheels. FITS: • JK Wrangler (2-door) w/ Dana 30 or 44 axle • JKU Wrangler Unlimited (4-door) w/ Dana 30 or 44 axle INCLUDES: • Upper ball joints w/out knurl - pair • Lower ball joints w/out knurl - pair Learn More

The TeraFlex TJ high steer trackbar kit is designed to be used in conjunction with our high steer kit. This kit will allow you to fine tune the drag link & trackbar angles to eliminate and correct bumpsteer or other front end issues. The kit includes an upper frame bracket, lower axle bracket, and adjustable trackbar. Both brackets feature multiple mounting holes to fine tune for lift height and trackbar position. This kit is designed to put the trackbar parallel with the drag link. This kit... Read More Learn More

The angled rod end forging is designed for applications needing additional clearance for tires, or other frame configurations. The Flex joint ends provide excellent off-road capabilities with articulation and durability. They dampen road noise and vibration. The forging uses standard 1-1/4” x 12 tpi. with a 9/16” center bolt. 10 degree angle off joint. Used on our JK Lower Control Arms for better Tire clearance in tight turns. Shoulder width= 2-5/8” Bolt dia.= 9/16” [14mm] Shank angle =... Read More Learn More

Large Rod End Field Repair Tool This repair tool will make joint rebuilding in the field as simple as it gets. This in fact is the same tool that we use in house to rebuild joints. The repair tool is easy to use with two open end wrenches, or sockets. Learn More

The TeraFlex is designed as an upgrade to a current suspension system. You get the same advantage and benefits of a long arm system without all of the cost from purchasing parts that you already own and have installed. *The Long Arm Upgrade Kit comes with all frame brackets, upper and lower long flexarms, and necessary hardware. Track bar brackets, and adjustable track bars are not included, but can be ordered separately. Details: Pro LCG Long Arm Bracket Kit Only For Use w/Lower... Read More Learn More

The TeraFlex FlexArm joint rebuild kit includes all required replacement components to rebuild a TeraFlex FlexArm joint. Depending on vehicle driving condtions, grit, grime, dust and fluids all take their toll on the tolerances of the bushings. To keep the joint functioning correctly it is necessary to rebuild the joint periodically and restore the joint to top working condition. This kit includes a chrome plated misalignment ball, two urethane bushings, large retainer washer, and snap ring. Learn More

The medium spherical urethane Monster end uses the same internals as its larger brother, in a scaled down version. The end utilizes a 7/8” x 18 tpi. shank and accepts a 7/16” bolt. Details: Right hand thread 2" shoulder width 7/8" x 18 TPI shank Accepts 7/16" bolt Shoulder Width = 2" Bolt Diameter = 12mm 7/8-18 UNS thread 1 1/4" wrench on jam nut Learn More

The large 23.5”w x 12”d table is designed to provide maximum use while on the trail, and folds vertical when not in use. The MP table is constructed from lightweight aluminum with stainless steel hardware and is rated for 75 lbs. of evenly distributed load capacity. The table also includes trash bag hooks, and a bottle opener. Multiple slots and holes allow for attaching accessories to the underside of the table. An optional polyethylene cutting board (#4804182) is available separately. Learn More